Vessel Lab

Try it free

Shape a printable bottle in your browser. Nothing to install, no account needed.

About Vessel Lab

Preview

Live 3D vessel preview

Checking…

One finger rotates · two fingers move and zoom · use full screen for detail

Design your vessel

Choose a starting shape, then refine its form and features. The 3D preview updates as you go.

Start again

Design name Used in your design library. This name is not printed on the model. Starting shape A round-bellied flask with a short neck. Uses a sloped shoulder instead of the prototype dome so it prints without supports.

Try it free. No account needed.

Shape

Heightmm Body widthmm Neck widthmm Shoulder position%

Maker sizes go up to 240 mm tall and 200 mm wide. Anyone can try them here; saving and printing past the free sizes needs Maker.

Body & shoulder

Base width% Side curve% Belly bulge% Belly height% Shoulder style Shoulder fullness%

Base edge rounding mm

Neck & lip

Neck lengthmm Neck bulge% Neck ringmm

Screw caps use a threaded neck, so the lip is set by the thread.

Cross-section

Shape seen from above Number of sides

Front-to-back depth%

Corner sharpness%

Shaped bodies blend back to round before the neck, so every closure still fits.

Surface textureMaker

Try any texture in the preview. Saving and printing a textured vessel needs Maker.

Pattern

Textures press outwards, so the wall never gets thinner. They fade out towards the neck and around the front motif, and are shaped to print without supports.

Handles & feetMaker

Try handles and feet in the preview. Saving and printing them needs Maker.

Handles Feet

Handle arms rise at 45°, so they print upright without supports. Feet print as their own file and push into sockets under the base, so the pot still prints flat; spread splays them outwards for a wider, steadier stance. A vessel on feet does not stand in a tray.

Closure

Type

Thread pitch mm Thread turns Fit clearance mm

Fit clearance is the gap between the parts. Raise it if the closure is too tight on your printer.

Closure texture & topMaker

Try a closure texture or top motif in the preview. Saving and printing them needs Maker.

Grip texture Motif on top

The grip band runs round the head of a cork or cap, or the rim of a lid, which is raised to carry it. Top motifs are engraved, because the top prints face-down on the bed.

Front motif

Motif

Style Edges

Sizemm Height on body% Relief depthmm

Sloped edges print on the upright bottle without supports, and the wall follows the motif so it keeps its thickness.

Colours

Body

Closure

Tray

The body, closure and any multicolour or glue-on parts keep their intended 3MF assignments.

Walls & base

Wall mm Base mm

The defaults suit a 0.4 mm nozzle. Thicker walls are stronger but hold less.

Create a free account to save it. Your design comes with you.

Print checks Show checks and print guide

Capacity: 141.1 ml
Widest: 76 mm
Neck bore: 20.4 mm
Thinnest wall: 1.8 mm

Wall thicknessThinnest wall is 1.80 mm (0.4 mm nozzle target 1.2 mm).
Support-free printingSteepest wall overhang is 48° from vertical when printed upright.
Print bed fitParts need 113 mm of a 256 mm bed.
Thread fitThreads overlap by 0.50 mm with 0.35 mm flank clearance.
Cap strengthCap wall is 1.80 mm and its top is 7.60 mm thick.
Motif reliefMoon raised 1.0 mm, 21 × 22 mm on the front face. 45° chamfer edges print without supports. The wall is pulled out behind it, so it stays 1.8 mm thick.
Surface textureThis vessel is smooth.
Drainage & trayNo drainage holes or tray.
Closure textureThe closure is smooth.
Top motifNo motif on the closure top.
HandlesNo handles on this vessel.
FeetThis vessel stands on its base.

Print & safety guide

Recommended settings

Nozzle: 0.4 mm
Layer height: 0.16 mm, for crisper threads and motif edges
Walls: 4 perimeters, so the 1.8 mm wall prints solid
Infill: 15% gyroid (only the base and closure use it)
Supports: None
Orientation: Body upright on its base, closure head-down beside it, as laid out in the 3MF
Material: PLA or PETG. PETG threads last longer if the cap is opened often.
Print area: 113 mm wide, 96 mm tall

Safety

Small parts: choking hazardThe screw cap is small enough to be a choking hazard. Not suitable for children under 3 years.
Not for food or drinkPrinted layers trap bacteria, most filaments are not food-contact certified, and printed vessels are not guaranteed watertight. Use for display and pretend play only.
CleaningWipe clean or hand-wash in lukewarm soapy water. Not dishwasher safe: PLA softens at around 55 °C.
Maker responsibilityWhoever prints and supplies this vessel is responsible for how it is made and for meeting local product-safety rules, including toy-safety requirements if it is sold as a toy.

Print file

Ready to print it?

Create a free account to save this design and download 3 free print files for your own use. Your design comes with you.

Create free account I already have an account

Multicolour 3MF laid out for your slicer, with a print and safety guide
Free files carry a small personal-use mark under the base
Maker adds more print files each month and commercial use